Cedar Park Metal Gates is the Texas capital region's trusted expert in commercial security fencing for yard owners, contractors and property managers, specializing in heavy tube steel panels, anti-climb pickets, long perimeter runs and the gate tie-ins that close them. We handle projects from a 60 lf lot frontage to a 600 lf perimeter, installed in sections so a working yard is never left open overnight.
Request a bid or a site walk
Our crews work occupied yards and storage lots, setting posts one run at a time so the business keeps its trucks, tenants and deliveries moving. Backed by 17 years in business and our 18-month workmanship warranty, we have completed over 1,483 projects, from a short frontage fence to full perimeters with vehicle gates, and references are available on request.
From the survey and the post layout to the gate tie-ins and the final walk, our team handles the parts of a perimeter job that decide whether the yard is secure by the end of each day. Serving Cedar Park, Georgetown, Round Rock and Leander, we hold the property manager's schedule, close each section before the crew leaves, and turn the line over ready for the owner's walkthrough.
Request a bid with your site plan, fence length and target dates, and we will schedule a site walk.
What you can hold us to
Gina, Airport Road, Georgetown
A light industrial owner tired of after-hours entry through an old chain link line
Investment and duration figures are estimates. Your written quote sets the final price and schedule.
Gina's light industrial yard on Airport Road in Georgetown needed a perimeter that stopped after-hours entry through an old chain link line. We installed 320 lf of heavy tube steel with a black powder coat, with 6 ft anti-climb panels. The crew worked in sections so the yard stayed closed every night. The job was an estimated $19,400 to $25,600 and took an estimated 3 to 4 days. The pickets are tight-spaced, with no climb rail on the outside.
The table sets the common commercial lines side by side.
| Lot | Typical fence | Weak spot | Est. investment |
|---|---|---|---|
| Contractor or truck yard | 6 ft anti-climb tube steel panels | Grade changes need stepped panels | Est. $19,400 to $25,600 for 320 lf |
| Storage lot or warehouse | Hand-forged iron fence with spear tops | Higher cost per lf than panel | Est. $88 to $128 per linear foot |
| Office park frontage | Ornamental tube steel fence line | Visible rust if the finish fails | Est. $52 to $83 per linear foot |
| Fence with a vehicle entry | Track slide gate with rack drive | Debris in the track | Est. $1,700 to $4,800 |
On a flat Georgetown or Round Rock lot, panels run straight and the posts set quickly. On a Leander or Lakeway hillside, pickets are racked to follow the grade up to the panel limit, then stepped.
Shop-forged scrolls and collars on a solid bar frame
4 to 6 foot panels on set posts along a yard or perimeter
A leaf on a V-track where the drive is flat and has side room for the open gate
Roller carriages and a counterbalance tail for sloped drives and heavy use
Rust treated and recoated rather than replacing sound old iron
Investment and duration figures are estimates. Your written quote sets the final price and schedule.
| Job type | Est. investment | Est. duration on site |
|---|---|---|
| Hand-forged iron fence | Est. $88 to $128 per linear foot | Est. 3 to 5 days |
| Ornamental tube steel fence line | Est. $52 to $83 per linear foot | Est. 2 to 4 days |
| Track slide gate with rack drive | Est. $1,700 to $4,800 per gate | Est. 2 to 3 days |
| Trackless cantilever gate | Est. $6,200 to $9,800 per gate | Est. 2 to 4 days |
| Old iron blast and recoat | Est. $31 to $48 per linear foot | Est. 1 to 3 days |
These figures are budgetary estimates for commercial perimeters and may change with grade, rock, panel height and the number of gates; the written quote that follows your site walk sets the final price and the schedule.
Posts go 36 inches deep on fence runs and 48 inches under gate posts, and a rock bit is on the truck for every Georgetown or Leander yard. A limestone ledge adds an estimated half day, named in the quote. Steiner Ranch and Lakeway hillside lots are shot with a level before any panel is ordered.
Bare steel is sandblasted, primed with zinc-rich primer and powder coated at the coater, never field paint on new steel. Hot-dip galvanizing comes first on fence near Round Rock drainage or Volente lake humidity, and the powder coat goes on after.
The steps run the same on every yard:
A vehicle gate on the line gets photo eyes and edges, and a hardwired 120V operator needs an electrical permit. On a Round Rock yard the Fire Marshal wants a city-approved Knox key switch on the gate and will not let it run until its acceptance test passes, so check the current text with the city. For Crystal Falls and Travisso gates, Leander has published Knox Box guidelines, so check the current text with the city before the gate is ordered. A Lakeway gate means handing the codes to police and fitting a key switch for Travis County ESD #6, and the city text should be rechecked before the order.
Gina's crew set posts one run at a time and hung panels in sections, so the yard stayed closed every night and the trucks kept their lane by day. Our lead welder fabricates gate frames and corner details in our shop, so a Georgetown or Leander run stays short on site.
Every fence carries our 18-month workmanship warranty on welds and post set, and every gate carries the maker's parts warranty, usually 1 to 5 years. Our owner has watched 17 years of Cedar Park yards grow, and 1,483 projects show in the references we offer.
We bid perimeter work across a 40-mile radius of Cedar Park, from Georgetown and Round Rock yards to Leander and Lakeway lots. Properties in Steiner Ranch, The Hills and Volente also fall within those 40 miles. Owners of a single home fence can start on our home page.
Each commercial buyer has a page built for its property: yard owners plan the entry on our commercial gates page, association boards plan gated community entry systems, and managers with several automated gates set up gate service contracts.
Six feet is common, as on the anti-climb panels on Airport Road, and the site walk confirms the height your lot needs.
320 lf took an estimated 3 to 4 days in Georgetown, and the written quote sets the schedule.
Yes, sections are closed every night before the crew leaves.
A rock bit is on the truck for limestone ledges, and the rock allowance is named in the quote.
Yes, a track slide gate with rack drive runs an estimated $1,700 to $4,800 and meets the new panels flush.
Yes, a site plan and fence length are enough for a first bid, and the site walk confirms the scope.
Request a bid with your site plan, fence length and target dates, and we will schedule the site walk.
Start to finish
An estimator walks the opening, reads the grade and marks where the leaf or the slide run has to clear.
Steel gets cut only after you sign off on a scaled drawing that names the tube, the coating and the opener.
Our Cedar Park welders build it, the steel goes for galvanizing and powder coat, and it ships finished.
Posts cure, the leaf goes up, the opener gets wired, and you watch each photo eye and edge stop the gate.
Services
Where we work
Call us or send a site plan, photos or a gate count, and we will set a site walk and return a written bid.
Calls only, we do not receive text messages.
