Cedar Park Metal Gates is the Texas capital region's trusted expert in gate replacement, specializing in steel leaves that replace warped wood gates, sagging frames and worn-out hardware. We offer measured, shop-built replacement gates hung on your existing masonry columns or steel posts, so the opening stays the same and the gate works again.
Get a free gate estimate
Our team provides measuring, fabrication, powder coating and hanging, delivering a gate that swings true for homes and a durable leaf for both residential and commercial projects. Backed by 17 years in business and our 18-month workmanship warranty, we've completed over 1,483 projects, from a 4 ft side gate to a 12 ft driveway leaf.
From the first tape pull across the opening to the final latch adjustment, our team handles the fabrication, the hinge set and the hang. Serving Cedar Park along with Round Rock, Georgetown and Leander, we hang each new gate so it closes and latches without a shoulder.
Request a free estimate, and we will tape the opening, probe the columns and price the new gate before any steel is cut.
What you can hold us to
Ignacio, Ranch at Brushy Creek, Cedar Park
A warped cedar gate twisted beyond adjustment, hung on good masonry columns
Investment and duration figures are estimates. Your written quote sets the final price and schedule.
Ignacio's driveway at Ranch at Brushy Creek in Cedar Park had a warped 12 ft cedar gate twisted beyond adjustment. We replaced it with a steel leaf hung on the existing masonry columns, so nothing around it had to be rebuilt. The job was an estimated $2,800 to $4,000 and took an estimated 1 to 2 days. The result is a straight new gate on columns that did not need to change.
A gate wears out at the hinge and the leaf long before the columns give up, which is why most Cedar Park replacements keep the opening and change the gate. The city grew from 26,049 people in 2000 to 77,595 in 2020, so many Buttercup Creek and Twin Creeks gates are now 20 years old. Ranch at Brushy Creek and Crystal Falls gates took the same heat and the same humidity, and wood leaves swell, sag and drag. Lake lot gates in Lakeway carry more weather off the water, while Steiner Ranch gates fight sun and slope.
A replacement gate in Cedar Park is priced to the leaf, and the width, the height, the column condition and any operator on the gate move the number most.
A single person-sized leaf with a keyed or magnetic latch
Rust treated and recoated rather than replacing sound old iron
Investment and duration figures are estimates. Your written quote sets the final price and schedule.
| Job | Est. investment | Est. duration on site |
|---|---|---|
| Walkway or courtyard entry gate | Est. $650 to $1,450 each | Est. 4 to 8 hours |
| Operator retrofit | Est. $1,900 to $3,700 | Est. 4 to 8 hours |
| Old iron blast and recoat | Est. $31 to $48 per linear foot | Est. 1 to 3 days |
| Access control | Est. $750 to $4,300 | Est. 4 to 8 hours |
A 12 ft driveway leaf on sound columns is an estimated 1 to 2 days at the shop-built price above, and a walk gate is often hung in a morning. Column condition, leaf height and an added operator can change these estimates, so the written quote you receive once we have probed your columns sets the final price and the schedule.
Replacement is the right call when the frame has warped or rusted through, and a blast and recoat is the better value when the frame is sound. Each row below pairs an option with its estimated price and the frame it suits.
| Option | Est. price | Best for |
|---|---|---|
| New steel leaf on existing columns | Est. $2,800 to $4,000 for a 12 ft leaf | Warped wood or a failed frame |
| Blast and recoat of an old iron gate | Est. $31 to $48 per linear foot | A sound frame with a tired finish |
| Operator retrofit on the new leaf | Est. $1,900 to $3,700 | A gate you want to open by remote |
A replacement goes in a set order, so the new leaf matches the old opening and the hinge loads are checked first. The process starts with the columns and ends with a swing test.
Steel is the standard replacement material, and our steel gate and fence material comparison explains galvanizing and powder coat. For a new walk gate beside the driveway, see our pedestrian entry gates, and for a gate that opens by remote see gate access control.
We measure the opening, weld the leaf and hang it ourselves, so the crew that probes your columns is the crew that sets your hinges. Across 17 years and 1,483 projects, our 18-month workmanship warranty has stood behind the welds, the hinge set and the travel of every gate we built. Ignacio's job shows the plain case: keep the masonry columns, replace the hinge plates and swap the wood for a steel leaf with a new operator, an estimated $2,800 to $4,000 over 1 to 2 days. Mina's Brodie Lane side leaf shows the other answer, since new hinges and a trued frame saved it for an estimated $1,900 to $2,700. Desmond's association board in Travisso replaced two sagging pairs one lane at a time for an estimated $9,800 to $14,200. Paige's 42 in walk gate in Hills of Lakeway, which replaced an old wood gate that stuck in humid weather, was an estimated $800 to $1,300.
We replace gates across a 40-mile radius, with gates in Round Rock, Georgetown and Leander, with every town we reach listed on the service area page. Georgetown acreage like Jerome's on Andice Road can need a wide leaf for trailers. Leander's Crystal Falls and Travisso homes are newer, so most orders replace a builder gate. In Round Rock the columns are checked first, and the city requires a Fire Marshal approved Knox key switch on an access-controlled gate. Steiner Ranch lots often sit on slope, and homes in The Hills need association approval first. Brodie Lane side and Slaughter Creek side homes in Shady Hollow date from 1972 on, and Lime Creek Road and Volente Road lake lots in Volente call for a galvanized leaf. Beckett's 14 ft leaf in Great Hills had sagged on its first post, so the replacement went on a new steel post and was cut to clear the grade. Emmett's leaf on the University Club side of Steiner Ranch needed two new posts bored through rock around buried utilities, an estimated $5,100 to $7,000. Shirin's 1970s gate on Westlake Drive did not need replacing, because a blast, two scroll repairs and a recoat saved it for an estimated $2,000 to $2,800.
A new gate usually pairs with an operator and access control, a matching walk gate, or custom driveway gates when the whole entry is changing.
Ignacio's warped 12 ft cedar gate at Ranch at Brushy Creek became a steel leaf on his existing columns for an estimated $2,800 to $4,000, and your own quote carries the final figure.
Hanging takes an estimated 1 to 2 days on site once the shop has built the leaf, and the dates go on your quote.
Yes, we probe the columns first and hang the new leaf on them when they are sound.
Replace a warped or rusted-through frame, and recoat a sound frame with a tired finish.
Yes, an operator retrofit is typically estimated at $1,900 to $3,700, and your quote names it.
The answer depends on which city covers your lot, so we look it up before you sign and note it on the quote.
Request a free estimate and we will tape the opening, probe the columns and write a quote that names the leaf, the hinges and the latch.
Start to finish
An estimator walks the opening, reads the grade and marks where the leaf or the slide run has to clear.
Steel gets cut only after you sign off on a scaled drawing that names the tube, the coating and the opener.
Our Cedar Park welders build it, the steel goes for galvanizing and powder coat, and it ships finished.
Posts cure, the leaf goes up, the opener gets wired, and you watch each photo eye and edge stop the gate.
Services
Where we work
Call us or send the form, and we will book a site measure and a written estimate.
Calls only, we do not receive text messages.
